Site Search:

Standard PSI Pressure Transducers

Pressure Transducer Measures 0-30 PSI, 0-50 PSI, 0-60 PSI, 0-100 PSI, 0-150 PSI, 0-200 PSI, and 0-500 PSI

Click here for -14.5 to 10000 PSI pressure transducers

Not all pressure transducers are built the same, click here to find out more before you order!

$39.99

Select Range: 

Measures 0-30 PSI

Tweet this page Like this product on Facebook Share this page on LinkedIn Email this page
2000361 Pressure Sensor
 

Description

The Pressure sensor measures 0-15 up to 0-500 PSI when connected to a Dataq Instruments Data Acquisition product or Data Logger.

The pressure sensor allows Dataq Instruments data acquisition and data logger units to acquire oil, fuel, air, brake fluid (DOT3/DOT4) or water pressure (PSI) information. The combination of these two products provides a compact solution, with transducer excitation provided by the data logger. The logger itself allows data to be communicated to a connected PC over either a USB or Ethernet interface. Optionally, many data loggers can store data to a removable USB thumb drive to satisfy stand-alone applications. Even with a connected pressure sensor, the data logger channel capacity allows additional channels of information to be acquired and correlated with pressure information to satisfy nearly any level of measurement expansion.

Not all pressure transducers are built the same

The diaphgram of pressure transducers can employ different material and technologies, and each one has its pros and cons. Here is the quick comparison table among the two types we offer

Product lines

2000361-H (0.5-4.5V output)

2000361-HX (4-20mA output)

2000361-CH (Customized model)

2000361
Material/Technologies Oil-filled diffusion silicon piezoresistive Dry ceramic capactitive
Not recommended for strong EMI environment
Output

2000361-H: 0.5-4.5V

2000361-HX: 4-20mA

2000361-CH: 0.5-4.5V or 4-20mA

0.5-4.5V
Pressure Type

Gauge pressure

Customization to Absolute pressure is available

Gauge pressure
Accuracy/Sensitivity ±0.5%FS
* Ranges lower than +5 PSI has 0.5-1% accuracy
±2% FS
Medium Any gas or liquid compatible with 316L stainless steel
(Not intended for acidic medium)
Any gas or liquid compatible with ceramic
Burst Pressure For transducers of full range up to 5000 PSI, 4 times span
For transducers of full range of 10000 PSI, 26000 PSI
4 times span
Overload Pressure For transducers of full range up to 5000 PSI, 2.5 times span
For transducers of full range of 10000 PSI, 14500 PSI
2.5 times span
Response Time 1ms 1ms
Working Temperture Range -40°C to 85°C -20°C to 70°C
Insulation Resistance 100ma 500VDC 100ma 500VDC
3D Model 1/4 NPT version  
Process Connection (Thread) 1/4" NPT-18 thread for 10000 psi
1/8" NPT-27 thread for the others (1/4 NPT" pipe fitting can be found here)
1/8" NPT-27 thread (1/4" NPT pipe fitting can be found here)
Electromagnetism Compatibility EN61326-1:2013
EN61326-2-2:2013
The EMC Directive2014/30/EU
EN61326-1:2013
EN61326-2-2:2013
The EMC Directive2014/30/EU
Supply Voltage 4.75-5.25V for 2000361-H (0.5-4.5V output model)

8-30V for 2000361-HX (4-20mA output model)
4.75-5.25V
Max Power Consumption

0.05W for 2000361-H (0.5-4.5V output model)

25mA*SupplyVoltage for 2000361-HX (4-20mA output model)

0.05W
Sealing Material NBR rubber
NBR rubber
Included Wiring Harness 3 ft (10ft harness can be found here) 3 ft (10ft harness can be found here)
Standard Ranges

-14.5 to 15, 30 psi

0 to -14.5, 15, 30, 50, 60, 100, 150, 200, 300, 500, 1000, 1500, 2000, 3000, 5000, 10000 psi

Customization available

0 to 30, 50, 60, 100, 150, 200, 500 psi
Customized Ranges -14.5 psi to 10000 psi NA
Cost $ 68 for 2000361-H (0.5-4.5V output model)

$ 79 for 2000361-HX (4-20mA output model, 250 Ohm shunt resistor included)

$ 99 for 2000361-CH (Typical lead time, 8 weeks)
$ 39.99

Accessories

101087-1

DC/DC Converter for Sensors

$24.99
DC/DC Converter

Description

Allows you to power 5V rating sensor with a battery. Input voltage: DC8-35V, (12V/24V changes to 5V); Output parameter: DC5V 3A, 15W MAX

2000361-PIGTAIL10

Extra 10-foot wire harness with mating connector

$15.95
Go to product page
DC/DC Converter

Description

10-foot long wire harness (pigtail) with mating connector and seal for pressure transducers

2000361-PIGTAIL

Spare wire harness with mating connector

$9.95
DC/DC Converter

Description

Spare 3-foot long wire harness (pigtail) with mating connector and seal for pressure transducers

2000361-PIPEFITTING

Stainless Steel Reducer Hex Bushing

$9.95
DC/DC Converter

Description

To convert pressure transducer fitting from 1/8 NPT to 1/4 MNPT
Max operating pressure: 2000 PSI

Specifications

Measurement Range: 2000361-30: 0 to 30 PSI
2000361-50: 0 to 50 PSI
2000361-60: 0 to 60 PSI
2000361-100: 0 to 100 PSI
2000361-150: 0 to 150 PSI
2000361-200: 0 to 200 PSI
2000361-500: 0 to 500 PSI
Material: 316 stainless steel and high temperature auto-graded plastic
Output: 0.5V – 4.5V linear voltage output
Supply Voltage: 5V +/-5%, 0.02W
Long Term Working Temperature: -20°C to 70°C
Accuracy: ±2%FS for ceramic pressure transducers.
Thread: 1/8” NPT-27
Protection Class: Typical IP65-66, depending on electric connection.
Overload Capacity: 2 times.
Pressure Medium: Any gas or liquid compatible with 316L stainless steel
Long-term stability: ± 0.5%FS/year
Response Time: ≤1ms
Insulation Resistance: >100mΩ 500VDC
Electromagnetism Compatibility: EN61326-1-2013
EN61325-2-2:2013
EMC Directive 2014/30/EU
Wiring connector: Water sealed quick-disconnect. Mating connector and wire harness (3 ft pigtail) included.
Wiring: Red for +5V Supply Voltage
Black for GND
Yellow or Green for OUT
Warranty: 90 days

Logger inaccuracy not included in these specifications.

Reviews